External wall insulation · Dorset
External wall insulation in Poole
Need external wall insulation in Poole? Tell us about the property and we'll arrange a free survey and a written quote. We plan EWI in Poole around the details that cause trouble later — cills, eaves, downpipes and the base of the wall above the damp-proof course.
- Free survey in BH15 and nearby
- Guide price from £105 per m² + scaffold, 0% VAT
- Fixed written price before work starts
Free survey in Poole
Postcode, service and a phone number is all we need.
What's included
- Boards chosen for the wall: EPS, mineral wool, wood fibre or phenolic
- Installing wall insulation in homes is currently zero-rated for VAT until 31 March 2027
- Typically takes a 225mm solid brick wall from around 2.1 W/m²K to about 0.30 W/m²K with 90–110mm of board
- Work happens outside, so you can live at home throughout
Homes and walls in Poole
As well as Poole itself, we quote in Bournemouth, Christchurch and New Milton. It's roughly 5 miles from Poole to Bournemouth, the largest town in Dorset. The South West has many stone and solid-walled cottages, exposed coastal properties and a share of post-war system-built houses, including types such as the Cornish Unit.
Exposure to wind-driven rain varies across Dorset: sheltered town streets fare better than walls on high ground or facing the prevailing weather, and the render, beads and cill details are chosen with that in mind.
Whole-house jobs and single elevations are both quoted in Poole; a cold gable or rear wall can be done on its own where it suits.
- Postcode district
- BH15
- County or area
- Dorset
- Nation
- England
- Nearby
- Bournemouth, Christchurch, New Milton, Dorchester
England: planning and regulations
For a house in Poole, external insulation or render is often permitted development if it looks similar to the existing walls; conservation areas, flats, commercial buildings and listed buildings need permission or consent, so we check your address first.
Building control applies once more than half of a wall is insulated or re-rendered, or more than a quarter of the whole building envelope, and your written quote says how that's handled.
How does external wall insulation work?
Heat moves out through a wall faster when the wall is solid or poorly insulated. EWI wraps the outside face in a continuous layer of insulation, so the masonry stays on the warm side and the cold bridges at floor and party-wall junctions are reduced. The boards are bonded with adhesive and, on most walls, mechanically fixed. A base coat with an embedded glass-fibre mesh goes over the top, then a primer and the decorative finish.
Because the wall itself sits inside the insulation, it stays warmer and drier, and the rooms keep their full size. That is the main difference from internal insulation.
External wall insulation prices in Poole
| Item | Guide price | Notes |
|---|---|---|
| EPS system with silicone render | £105–£145 per m²0% VAT | Most common choice for houses |
| Mineral wool system | £125–£170 per m²0% VAT | Non-combustible, vapour-open |
| Brick-slip finish over insulation | £185–£260 per m²0% VAT | Where a brick look is wanted |
| Three-bed semi, EPS + silicone (incl. scaffold) | £10,200–£17,7000% VAT | 80–100 m² of wall; depends on detailing and access |
Confirmed by a fixed written quote after survey. 0% VAT: installing insulation in a home is zero-rated until 31 March 2027, so these figures are the total; 5% applies from 1 April 2027.
What happens next
Enquiry
Send your postcode and a few details.
Measured survey
Walls, damp, eaves, cills and services recorded.
Written price
A fixed price with the specification attached.
Work and handover
Installed, inspected and documents handed over.
External wall insulation in Poole: questions
Can EWI go over pebble dash?
Usually yes. The dash is tested for adhesion and hollow areas; sound dash can be insulated over with additional mechanical fixings, while loose areas are removed first.
Does external wall insulation cause damp?
Not when it is specified and detailed properly. Problems usually come from poor detailing: no starter track above the damp-proof course, gaps at cills and penetrations, or a vapour-closed system on a wall that needs to breathe. The survey checks moisture, ground levels and the wall type before a system is chosen.
Do I need planning permission for external wall insulation?
Often not for a house in England or Wales if the finish looks similar to the existing walls. You will usually need permission in a conservation area, on flats, on commercial buildings or where the appearance changes noticeably. Listed buildings need listed building consent. We check your address before quoting.
Do you cover Poole?
Yes — we survey and quote external wall insulation in Poole (BH15) and nearby Bournemouth, Christchurch and New Milton, with a fixed written price before any work starts.