External wall insulation · Greater London
External wall insulation in Catford
From Catford to Blackheath, we price external wall insulation after a measured survey — no guesswork, and no work starts until the price is agreed in writing. For homes in Catford, the survey starts with the wall itself: solid brick, stone or concrete, and whether any old render is sound enough to insulate over.
- Free survey in SE6 and nearby
- Guide price from £105 per m² + scaffold, 0% VAT
- Fixed written price before work starts
Free survey in Catford
Postcode, service and a phone number is all we need.
What you get
- Typically takes a 225mm solid brick wall from around 2.1 W/m²K to about 0.30 W/m²K with 90–110mm of board
- Cills, pipes, vents, meter boxes and the roofline detailed as part of the job
- Boards chosen for the wall: EPS, mineral wool, wood fibre or phenolic
- Work happens outside, so you can live at home throughout
What we look for in Catford
We cover Catford and nearby Blackheath, Beckenham and Peckham. London's housing includes a large stock of Victorian and Edwardian solid-wall terraces, inter-war semis and post-war blocks, and conservation areas cover many streets — so planning is often the first question for external work.
Much of Greater London sits in the lower wind-driven rain exposure bands, which keeps the choice of finishes wide — though hilltop, coastal and exposed gable walls can still need a tougher specification, so we check the actual site.
Whole-house jobs and single elevations are both quoted in Catford; a cold gable or rear wall can be done on its own where it suits.
- Postcode district
- SE6
- County or area
- Greater London
- Nation
- England
- Nearby
- Blackheath, Beckenham, Peckham, Eltham
Approvals in England
Planning in Catford follows England's national rules: similar-looking finishes on houses are usually permitted, while flats, commercial premises, conservation areas and streets under an Article 4 direction need an application.
Insulating or re-rendering more than half of a wall's area brings in Part L of the Building Regulations, so building control is notified and the wall is upgraded to about 0.30 W/m²K where practical.
How does external wall insulation work?
Heat moves out through a wall faster when the wall is solid or poorly insulated. EWI wraps the outside face in a continuous layer of insulation, so the masonry stays on the warm side and the cold bridges at floor and party-wall junctions are reduced. The boards are bonded with adhesive and, on most walls, mechanically fixed. A base coat with an embedded glass-fibre mesh goes over the top, then a primer and the decorative finish.
Because the wall itself sits inside the insulation, it stays warmer and drier, and the rooms keep their full size. That is the main difference from internal insulation.
External wall insulation prices in Catford
| Item | Guide price | Notes |
|---|---|---|
| EPS system with silicone render | £105–£145 per m²0% VAT | Most common choice for houses |
| Mineral wool system | £125–£170 per m²0% VAT | Non-combustible, vapour-open |
| Brick-slip finish over insulation | £185–£260 per m²0% VAT | Where a brick look is wanted |
| Three-bed semi, EPS + silicone (incl. scaffold) | £10,200–£17,7000% VAT | 80–100 m² of wall; depends on detailing and access |
Confirmed by a fixed written quote after survey. 0% VAT: installing insulation in a home is zero-rated until 31 March 2027, so these figures are the total; 5% applies from 1 April 2027.
How it works
Tell us about the property
Use the quote tool or form, or call. Photos help.
Free survey
We measure, check the walls and confirm approvals.
Fixed written quote
System, details, access, exclusions and VAT in writing.
Installation
Scheduled for suitable weather, with a clear programme.
External wall insulation in Catford: questions
Can EWI go over pebble dash?
Usually yes. The dash is tested for adhesion and hollow areas; sound dash can be insulated over with additional mechanical fixings, while loose areas are removed first.
Does external wall insulation cause damp?
Not when it is specified and detailed properly. Problems usually come from poor detailing: no starter track above the damp-proof course, gaps at cills and penetrations, or a vapour-closed system on a wall that needs to breathe. The survey checks moisture, ground levels and the wall type before a system is chosen.
How long does external wall insulation last?
A well-installed render system is commonly expected to last 25–30 years or more, with occasional cleaning and inspection of sealants. The system manufacturer's documentation states the expected service life for the specific build-up.
Do you cover Catford?
Yes — we survey and quote external wall insulation in Catford (SE6) and nearby Blackheath, Beckenham and Peckham, with a fixed written price before any work starts.