External wall insulation · Isle of Wight
External wall insulation in Sandown
Homeowners and landlords in Sandown can get a free survey and a fixed written quote for external wall insulation, covering PO36 and the surrounding area. For homes in Sandown, the survey starts with the wall itself: solid brick, stone or concrete, and whether any old render is sound enough to insulate over.
- Free survey in PO36 and nearby
- Guide price from £105 per m² + scaffold, 0% VAT
- Fixed written price before work starts
Free survey in Sandown
Postcode, service and a phone number is all we need.
What the job covers
- Boards chosen for the wall: EPS, mineral wool, wood fibre or phenolic
- Cills, pipes, vents, meter boxes and the roofline detailed as part of the job
- Installing wall insulation in homes is currently zero-rated for VAT until 31 March 2027
- Typically takes a 225mm solid brick wall from around 2.1 W/m²K to about 0.30 W/m²K with 90–110mm of board
Homes and walls in Sandown
We also cover Ryde and Newport (Isle of Wight), close to Sandown. Sandown sits around 5 miles from Ryde. Homes across the South East range from inter-war semis and post-war estates, which are mostly cavity-walled, to older solid-walled cottages and Victorian town terraces.
Exposure to wind-driven rain varies across Isle of Wight: sheltered town streets fare better than walls on high ground or facing the prevailing weather, and the render, beads and cill details are chosen with that in mind.
We plan EWI in Sandown around the details that cause trouble later — cills, eaves, downpipes and the base of the wall above the damp-proof course.
- Postcode district
- PO36
- County or area
- Isle of Wight
- Nation
- England
- Nearby
- Ryde, Newport (Isle of Wight), Cowes, Gosport
England: planning and regulations
Planning in Sandown follows England's national rules: similar-looking finishes on houses are usually permitted, while flats, commercial premises, conservation areas and streets under an Article 4 direction need an application.
Building control applies once more than half of a wall is insulated or re-rendered, or more than a quarter of the whole building envelope, and your written quote says how that's handled.
How does external wall insulation work?
Heat moves out through a wall faster when the wall is solid or poorly insulated. EWI wraps the outside face in a continuous layer of insulation, so the masonry stays on the warm side and the cold bridges at floor and party-wall junctions are reduced. The boards are bonded with adhesive and, on most walls, mechanically fixed. A base coat with an embedded glass-fibre mesh goes over the top, then a primer and the decorative finish.
Because the wall itself sits inside the insulation, it stays warmer and drier, and the rooms keep their full size. That is the main difference from internal insulation.
External wall insulation prices in Sandown
| Item | Guide price | Notes |
|---|---|---|
| EPS system with silicone render | £105–£145 per m²0% VAT | Most common choice for houses |
| Mineral wool system | £125–£170 per m²0% VAT | Non-combustible, vapour-open |
| Brick-slip finish over insulation | £185–£260 per m²0% VAT | Where a brick look is wanted |
| Three-bed semi, EPS + silicone (incl. scaffold) | £10,200–£17,7000% VAT | 80–100 m² of wall; depends on detailing and access |
Confirmed by a fixed written quote after survey. 0% VAT: installing insulation in a home is zero-rated until 31 March 2027, so these figures are the total; 5% applies from 1 April 2027.
What happens next
Tell us about the property
Use the quote tool or form, or call. Photos help.
Free survey
We measure, check the walls and confirm approvals.
Fixed written quote
System, details, access, exclusions and VAT in writing.
Installation
Scheduled for suitable weather, with a clear programme.
External wall insulation in Sandown: questions
Can EWI go over pebble dash?
Usually yes. The dash is tested for adhesion and hollow areas; sound dash can be insulated over with additional mechanical fixings, while loose areas are removed first.
Does EWI need Building Regulations approval?
In England and Wales, usually. Insulating more than half of a wall's area, or more than a quarter of the building's whole external envelope, counts as renovating a thermal element, so building control needs to be involved and the wall should reach about 0.30 W/m²K where that's practical. Scotland and Northern Ireland have their own building standards processes.
Does external wall insulation cause damp?
Not when it is specified and detailed properly. Problems usually come from poor detailing: no starter track above the damp-proof course, gaps at cills and penetrations, or a vapour-closed system on a wall that needs to breathe. The survey checks moisture, ground levels and the wall type before a system is chosen.
Do you cover Sandown?
Yes — we survey and quote external wall insulation in Sandown (PO36) and nearby Ryde, Newport (Isle of Wight) and Cowes, with a fixed written price before any work starts.