Silicone render · Leicestershire
Silicone render in Melton Mowbray
If you're planning silicone render in Melton Mowbray, start with a free survey: we measure, check the walls and confirm planning and building control for your address. On tree-shaded or north-facing walls in Melton Mowbray, silicone's water repellence helps it stay cleaner for longer.
- Free survey in LE13 and nearby
- Guide price from £66 per m² + scaffold, inc VAT
- Fixed written price before work starts
Free survey in Melton Mowbray
Postcode, service and a phone number is all we need.
Included as standard
- Through-coloured — no painting needed
- Fine, even grain from about 1–2mm
- Can also go straight onto prepared masonry
- Used as the finish on most EWI systems
Local considerations in Melton Mowbray
As well as Melton Mowbray itself, we quote in Oakham, Loughborough and Leicester. It's roughly 14 miles from Melton Mowbray to Leicester, the largest town in Leicestershire. Housing in the East Midlands includes Victorian terraces in the towns and cities, plenty of inter-war semis and post-war council estates, some of them system-built.
Much of Leicestershire sits in the lower wind-driven rain exposure bands, which keeps the choice of finishes wide — though hilltop, coastal and exposed gable walls can still need a tougher specification, so we check the actual site.
If you're re-rendering in Melton Mowbray, we'll show you what adding insulation under the silicone would cost at the same time.
- Postcode district
- LE13
- County or area
- Leicestershire
- Nation
- England
- Nearby
- Oakham, Loughborough, Leicester, Oadby
Approvals in England
Planning in Melton Mowbray follows England's national rules: similar-looking finishes on houses are usually permitted, while flats, commercial premises, conservation areas and streets under an Article 4 direction need an application.
Insulating or re-rendering more than half of a wall's area brings in Part L of the Building Regulations, so building control is notified and the wall is upgraded to about 0.30 W/m²K where practical.
Silicone or monocouche?
Monocouche is a thicker single-coat cement render used mainly on new blockwork. Silicone is thinner, more flexible and usually more resistant to staining, and it's the finish used over insulation. On older or mixed walls, silicone over a mesh-reinforced base coat is generally the safer choice.
Silicone render prices in Melton Mowbray
| Item | Guide price | Notes |
|---|---|---|
| Silicone render on masonry (with base coat + mesh) | £66–£102 per m²inc VAT | Excluding scaffold |
| Front and side of a semi (≈60 m²) | £3,960–£6,120inc VAT | Plus scaffold |
| As the finish on EWI | Included in EWI rates |
Confirmed by a fixed written quote after survey. Prices include VAT at 20%.
What happens next
Enquiry
Send your postcode and a few details.
Measured survey
Walls, damp, eaves, cills and services recorded.
Written price
A fixed price with the specification attached.
Work and handover
Installed, inspected and documents handed over.
Silicone render in Melton Mowbray: questions
How long does silicone render take to dry?
It's touch-dry within hours but needs dry weather above about 5°C for the first day or two to cure properly.
Can I paint silicone render later?
Yes, with a compatible silicone paint, though through-coloured render rarely needs it.
Can silicone render go over old render?
If the old render is sound and well bonded, often yes after cleaning and priming. Hollow or cracked areas are cut out and repaired first.
Do you cover Melton Mowbray?
Yes — we survey and quote silicone render in Melton Mowbray (LE13) and nearby Oakham, Loughborough and Leicester, with a fixed written price before any work starts.