External wall insulation · Hampshire
External wall insulation in Hythe
If you're planning external wall insulation in Hythe, start with a free survey: we measure, check the walls and confirm planning and building control for your address. Whole-house jobs and single elevations are both quoted in Hythe; a cold gable or rear wall can be done on its own where it suits.
- Free survey in SO45 and nearby
- Guide price from £105 per m² + scaffold, 0% VAT
- Fixed written price before work starts
Free survey in Hythe
Postcode, service and a phone number is all we need.
What you get
- Work happens outside, so you can live at home throughout
- Boards chosen for the wall: EPS, mineral wool, wood fibre or phenolic
- Typically takes a 225mm solid brick wall from around 2.1 W/m²K to about 0.30 W/m²K with 90–110mm of board
- Covers tired brick, pebble dash or failing render with a new finish
Homes and walls in Hythe
We cover Hythe and nearby Southampton, Totton and Eastleigh. Hythe sits around 3 miles from Southampton. Homes across the South East range from inter-war semis and post-war estates, which are mostly cavity-walled, to older solid-walled cottages and Victorian town terraces.
Exposure to wind-driven rain varies across Hampshire: sheltered town streets fare better than walls on high ground or facing the prevailing weather, and the render, beads and cill details are chosen with that in mind.
We plan EWI in Hythe around the details that cause trouble later — cills, eaves, downpipes and the base of the wall above the damp-proof course.
- Postcode district
- SO45
- County or area
- Hampshire
- Nation
- England
- Nearby
- Southampton, Totton, Eastleigh, Cowes
England: planning and regulations
Planning in Hythe follows England's national rules: similar-looking finishes on houses are usually permitted, while flats, commercial premises, conservation areas and streets under an Article 4 direction need an application.
If the work covers more than half of a wall, or a quarter of the building's whole envelope, it counts as renovating a thermal element, with a target of about 0.30 W/m²K where feasible.
How does external wall insulation work?
Heat moves out through a wall faster when the wall is solid or poorly insulated. EWI wraps the outside face in a continuous layer of insulation, so the masonry stays on the warm side and the cold bridges at floor and party-wall junctions are reduced. The boards are bonded with adhesive and, on most walls, mechanically fixed. A base coat with an embedded glass-fibre mesh goes over the top, then a primer and the decorative finish.
Because the wall itself sits inside the insulation, it stays warmer and drier, and the rooms keep their full size. That is the main difference from internal insulation.
External wall insulation prices in Hythe
| Item | Guide price | Notes |
|---|---|---|
| EPS system with silicone render | £105–£145 per m²0% VAT | Most common choice for houses |
| Mineral wool system | £125–£170 per m²0% VAT | Non-combustible, vapour-open |
| Brick-slip finish over insulation | £185–£260 per m²0% VAT | Where a brick look is wanted |
| Three-bed semi, EPS + silicone (incl. scaffold) | £10,200–£17,7000% VAT | 80–100 m² of wall; depends on detailing and access |
Confirmed by a fixed written quote after survey. 0% VAT: installing insulation in a home is zero-rated until 31 March 2027, so these figures are the total; 5% applies from 1 April 2027.
How it works
Enquiry
Send your postcode and a few details.
Measured survey
Walls, damp, eaves, cills and services recorded.
Written price
A fixed price with the specification attached.
Work and handover
Installed, inspected and documents handed over.
External wall insulation in Hythe: questions
How much does external wall insulation cost?
Our guide price for EWI is £105–£170 per m² of wall depending on the system, plus scaffolding. A typical three-bed semi with EPS and silicone render comes to roughly £10,200–£17,700 for the whole house, including scaffold. Installing insulation in a home is zero-rated for VAT until 31 March 2027, so that's the total. You get a fixed written price after a free survey.
Do I need planning permission for external wall insulation?
Often not for a house in England or Wales if the finish looks similar to the existing walls. You will usually need permission in a conservation area, on flats, on commercial buildings or where the appearance changes noticeably. Listed buildings need listed building consent. We check your address before quoting.
Does EWI need Building Regulations approval?
In England and Wales, usually. Insulating more than half of a wall's area, or more than a quarter of the building's whole external envelope, counts as renovating a thermal element, so building control needs to be involved and the wall should reach about 0.30 W/m²K where that's practical. Scotland and Northern Ireland have their own building standards processes.
Do you cover Hythe?
Yes — we survey and quote external wall insulation in Hythe (SO45) and nearby Southampton, Totton and Eastleigh, with a fixed written price before any work starts.