External wall insulation · Tyne and Wear
External wall insulation in Washington
Looking for external wall insulation in Washington? We survey homes across Washington and the NE37 area, then give you a fixed written price before any work starts. Whole-house jobs and single elevations are both quoted in Washington; a cold gable or rear wall can be done on its own where it suits.
- Free survey in NE37 and nearby
- Guide price from £105 per m² + scaffold, 0% VAT
- Fixed written price before work starts
Free survey in Washington
Postcode, service and a phone number is all we need.
Part of every quote
- Cills, pipes, vents, meter boxes and the roofline detailed as part of the job
- Covers tired brick, pebble dash or failing render with a new finish
- Boards chosen for the wall: EPS, mineral wool, wood fibre or phenolic
- Typically takes a 225mm solid brick wall from around 2.1 W/m²K to about 0.30 W/m²K with 90–110mm of board
What we look for in Washington
We also cover Chester-le-Street and Felling, close to Washington. It's roughly 6 miles from Washington to Newcastle upon Tyne, the largest town in Tyne and Wear. The North East has many solid brick terraces, including former colliery housing, plus post-war council estates with some system-built homes.
Exposure to wind-driven rain varies across Tyne and Wear: sheltered town streets fare better than walls on high ground or facing the prevailing weather, and the render, beads and cill details are chosen with that in mind.
For homes in Washington, the survey starts with the wall itself: solid brick, stone or concrete, and whether any old render is sound enough to insulate over.
- Postcode district
- NE37
- County or area
- Tyne and Wear
- Nation
- England
- Nearby
- Chester-le-Street, Felling, Houghton-le-Spring, Sunderland
Approvals in England
Before quoting in Washington, we check whether the property is in a conservation area, under an Article 4 direction or listed, because that decides whether changing the outside needs planning permission.
Building control applies once more than half of a wall is insulated or re-rendered, or more than a quarter of the whole building envelope, and your written quote says how that's handled.
How does external wall insulation work?
Heat moves out through a wall faster when the wall is solid or poorly insulated. EWI wraps the outside face in a continuous layer of insulation, so the masonry stays on the warm side and the cold bridges at floor and party-wall junctions are reduced. The boards are bonded with adhesive and, on most walls, mechanically fixed. A base coat with an embedded glass-fibre mesh goes over the top, then a primer and the decorative finish.
Because the wall itself sits inside the insulation, it stays warmer and drier, and the rooms keep their full size. That is the main difference from internal insulation.
External wall insulation prices in Washington
| Item | Guide price | Notes |
|---|---|---|
| EPS system with silicone render | £105–£145 per m²0% VAT | Most common choice for houses |
| Mineral wool system | £125–£170 per m²0% VAT | Non-combustible, vapour-open |
| Brick-slip finish over insulation | £185–£260 per m²0% VAT | Where a brick look is wanted |
| Three-bed semi, EPS + silicone (incl. scaffold) | £10,200–£17,7000% VAT | 80–100 m² of wall; depends on detailing and access |
Confirmed by a fixed written quote after survey. 0% VAT: installing insulation in a home is zero-rated until 31 March 2027, so these figures are the total; 5% applies from 1 April 2027.
From enquiry to finished wall
Tell us about the property
Use the quote tool or form, or call. Photos help.
Free survey
We measure, check the walls and confirm approvals.
Fixed written quote
System, details, access, exclusions and VAT in writing.
Installation
Scheduled for suitable weather, with a clear programme.
External wall insulation in Washington: questions
Does external wall insulation cause damp?
Not when it is specified and detailed properly. Problems usually come from poor detailing: no starter track above the damp-proof course, gaps at cills and penetrations, or a vapour-closed system on a wall that needs to breathe. The survey checks moisture, ground levels and the wall type before a system is chosen.
How much does external wall insulation cost?
Our guide price for EWI is £105–£170 per m² of wall depending on the system, plus scaffolding. A typical three-bed semi with EPS and silicone render comes to roughly £10,200–£17,700 for the whole house, including scaffold. Installing insulation in a home is zero-rated for VAT until 31 March 2027, so that's the total. You get a fixed written price after a free survey.
Does EWI need Building Regulations approval?
In England and Wales, usually. Insulating more than half of a wall's area, or more than a quarter of the building's whole external envelope, counts as renovating a thermal element, so building control needs to be involved and the wall should reach about 0.30 W/m²K where that's practical. Scotland and Northern Ireland have their own building standards processes.
Do you cover Washington?
Yes — we survey and quote external wall insulation in Washington (NE37) and nearby Chester-le-Street, Felling and Houghton-le-Spring, with a fixed written price before any work starts.